I have been playing with a new Triquint ULNA device (TQP3M9036). It
Shows a lot of promise. It is like a MAR or MSA device in that it is
50ohm in and out. and has a claimed NF about .4db nf ( their numbers).
I have built several pramps to test them and have gotten even better
than they claim and they cover 50-1296 with ease and NF is .4ish or
below. The S11 and S22 are both great and the OIP3 is +35db also
...very nice device. It has great promise as a good terrestrial LNA.
Preamps are foolproof to build and would cost under $50 if all the best
quality parts are used.
Just for information only ...
Pete WA2ODO
--
++++++CONFIDENTIALITY NOTICE++++++
The information in this email may be confidential and/or privileged. This email is intended to be reviewed by only the individual or organization named above. If you are not the intended recipient or an authorized representative of the intended recipient, you are hereby notified that any review, dissemination or copying of this email and its attachments, if any, or the information contained herein is prohibited. If you have received this email in error, please immediately notify the sender by return email and delete this email from your system.
Hi all,
I’m ready on 6cm with the same dish I’m using on 3cm.
Despite the strong local 5 GHz WiFi noise, had a nice 579/569 first QSO with this setup today with HB9Q, thank you Dan !
Setup is a 3.7m dish and 60W at CP feeder.
I can be QRV on 6cm or 3cm most of the days, skeds and tests are very welcome, as usual.
Vy 73
Bruce PY2BS
qrv 70cm, 33cm, 23cm, 13cm, 9cm, 6cm and 3cm.
Hello to Lunatics.
Owners of RAS 1deg. and RAS 0.5 deg. rotators and Rot2Prog controllers
can try my free Ras Moon Tracker program.
Program was fully tested with RAS 1deg. rotator by me, because I have
it and use it.
Program can be downloaded here :
https://1drv.ms/u/s!Auurs2F0cQKF1DSJ2vdO6JjJwEOX
Program do not required any installation, open archive and extract
program folder to ur C:\ or any other drive.
Best Wishes.
de 4z5cp
I have 4 Andrew C112HNSG waveguide to coax transitions available. These are
new old stock, still in the factory packaging with gasket and screws. $60
each, shipped, offers considered. Photos available. Email me directly,
please.
Thanks,
Robin Midgett K4IDC
_._,_._,_
------------------------------
I have 3 working elecraft transverters… 50,144,432… all work properly.
Even have a HB switch unit to control 4 xvtrs using HP 4pst relays..
These were used with a flex 5k (have 2.) 2rx and ant tuner.
EME ant sys. 4 m2 12el 144 (var polarity), 4 FO25 432, M2 mt3000 el rotor
w/ green heron, M2 2800 AZ with Green Heron, TriEx LM470D 72FT motorized
crank up,. Cables, harnesses, power dividers, preamps and hp N
relays.... And more. (Still up… but easy take down as tower lays down and
tilts over.
Discuss off any and/or all list or phone if interested.
Pete wa2odo
Ft. Mill, SC
I have 4 icom ic-970's (various models) 1 for parts only, 1 as all
modules inc. 1296 and the rare 2304. Other has 1296 and one just std.
Any interest? Will discuss off list. All except parts work properly.
Pete wa2odo
Ft. Mill, SC
Hello all,
I have a Rohde + Schwarz 90 deg angled adaptor male-male "RS LNW 2002/60"
sitting on my desk, mainly used as paperweight for some 20 years now. It is
marked "RS LNW 2002/60". I do not know the impedance but from the name I
presume it is 60 Ohms.
Can anyone confirm the 60 Ohms? Google did not help in this case.
If anybody wants to have it please mail me off-list @ BerndDF2ZC(a)gmail.com.
I can provide photo of course.
vy 73 Bernd DF2ZC
<http://www.df2zc.de> www.df2zc.de
____________________________________________
144 MHz EME NewsLetter:
<http://www.df2zc.de/newsletter> www.df2zc.de/newslettertwitter.com/df2zc
144 MHz DXCC #21
144 MHz WAC
Kenwood TS 2000
2 x GU74b by LZ2US
BEKO HLV-2000
4 x 2M18XXX 21 dBd full elevation
